Description
The WAGO 787-1221 switched-mode power supply features Compact, 1-phase, 12 VDC output voltage, 8 A output current, DC-OK LED.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x AC 100 ... 240 V
- Input voltage range: 1 x 90 … 264 VAC; 125 … 375 VDC
- Input voltage derating: -2 %/V (< 100 VAC); -1.33 %/V (< 140 VDC)
- Nominal mains frequency range: 47 … 63 Hz; 0 Hz
- Input current Ii: ≤ 1.6 A (100 VAC; 8 ADC)
- Inrush current: ≤ 30 A (NTC)
- Power factor: ≥ 0.5
- Power factor correction (PFC): Passive
- Mains failure hold-up time: ≥ 50 ms (230 VAC)
- Nominal output voltage [V]: 12 VDC (SELV)
- Output voltage range: DC 12 V
- Default Setting: 12 VDC
- Nominal output current Io nom: 8 A
- Nominal output power: 96 W
- Deviation: ≤ 1 %
- Deviation, dynamic load change 10 … 90 %: ≤ 1 %
- Residual ripple: ≤ 100 mV (peak-to-peak)
- Overload behavior: Constant power (in overload range: 1.05 … 1.35 x Io nom); Shutdown and automatic restart in the event of a short circuit or permanent overload
- Signaling: 1 x DC OK LED (green)
- Operation status indicator: Green LED (Uo)
- Power loss Pl: ≤ 0.7 W
- Power loss (max.) Pl (max.): 11.8 W (100 VAC / 12 VDC; 8 A)
- Efficiency (typ.): 91.5 % (230 VAC; Nominal load); 90 % (110 VAC; Nominal load)
- Internal fuse: T 3.15 A / 250 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): Circuit breaker: 6 A, 10 A or higher; Tripping characteristic: B
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Isolation voltage (pri.-PE): 2.12 kVDC
- Protection class: I
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 16 VDC
- Overvoltage category: II
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Overvoltage protection; secondary: ≤ 20 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes, for 2 devices of the same type
- MTBF: > 1,300,000 h (at 25 C; per IEC 61709); > 250,000 h (at 40 C; per IEC 61709)
- Connection Data — Cable length (max.): 30 m
- Connection 1 — Connection type: Input/output
- Connection 1 — Connection technology: Push-in CAGE CLAMP®
- Connection 1 — WAGO connector: picoMAX® 5.0, WAGO 2092 Series
- Connection 1 — Solid conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
- Connection 1 — Strip length: 9 … 10 mm / 0.35 … 0.39 inches
- Width: 108 mm / 4.252 inches
- Height: 90 mm / 3.543 inches
- Depth: 56 mm / 2.205 inches
- Depth from upper-edge of DIN-rail: 52.5 mm / 2.067 inches
- Housing design: DIN-rail-mount enclosure
- Mounting type: DIN-35 rail; Screw mount (back)
- Flammability class per UL94: V0
- Weight: 422.8 g
- Ambient temperature (operation): -25 … +70 °C
- Ambient temperature (storage): -40 … +85 °C
- Relative humidity: 20 … 90 % (no condensation permissible)
- Derating: -2 %/K (> 45 °C)
- Climatic category: 3K3 (per EN 60721; except for low air pressure)
- Conformity marking: CE
- Standards/specifications: EN 61204-3; EN 60335-1; UL 508
Image shown is representative. Refer to the product specifications for the exact configuration.