null

WAGO 787-1200 Switched-mode power supply, Compact, 1-phase, 24 VDC output voltage, 0.5 A output current, DC-OK LED

$56.44
SKU:
787-1200
Shipping:
Calculated at Checkout
In Stock
Available
Before Ordering

Availability and lead times may vary. Request a quote if you need to confirm availability before placing your order.


Manufacturer Information

Wago orders require a $100 combined minimum order.

Family Owned Since 1932
Nationwide Shipping Serving all 50 states
Technical Support Product selection assistance
Project Assistance Quotes and sourcing support

Description

The WAGO 787-1200 switched-mode power supply features Compact, 1-phase, 24 VDC output voltage, 0.5 A output current, DC-OK LED.

Specifications

  • Phases: 1
  • Nominal input voltage [V]: 1 x 100 … 240 VAC
  • Input voltage range: 1 x 90 … 264 VAC
  • Input voltage derating: -2 %/V (< 100 VAC)
  • Nominal mains frequency range: 47 … 63 Hz
  • Input current Ii: ≤ 0.27 A (100 VAC; 0.5 ADC)
  • Inrush current: ≤ 30 A (NTC)
  • Power factor: ≥ 0.5
  • Power factor correction (PFC): None
  • Mains failure hold-up time: ≥ 100 ms (230 VAC)
  • Nominal output voltage [V]: 24 VDC (SELV)
  • Nominal output current Io nom: 0.5 A
  • Nominal output power: 12 W
  • Deviation: ≤ 1 %
  • Deviation, dynamic load change 10 … 90 %: ≤ 1 %
  • Residual ripple: ≤ 100 mV (peak-to-peak)
  • Overload behavior: shutdown and automatic restart in the event of a short circuit
  • Signaling: 1 x Status indication LED (green)
  • Operation status indicator: Green LED (Uo)
  • Power loss Pl: ≤ 0.2 W
  • Power loss (max.) Pl (max.): 2.5 W (100 VAC / 24 VDC; 0.5 A)
  • Efficiency (typ.): 83 % (230 VAC; nominal load); 82 % (110 VAC; nominal load)
  • Internal fuse: T 1 A / 250 VAC
  • Pre-fuse (required): An external DC fuse is required for the DC input voltage.
  • Backup fuse (recommended): Circuit breaker: 6 A (C characteristic), 10 A (B characteristic) or higher
  • Isolation voltage (pri.-sec.): 4.242 kVDC
  • Protection class: II
  • protection rating: IP20; per EN 60529
  • Reverse voltage protection: Yes
  • Resistance to reverse feed: ≤ 31 VDC
  • Overvoltage category: II
  • Pollution degree: 2
  • Transient suppression (primary): Yes
  • Overvoltage protection; secondary: ≤ 31 VDC (in the event of a fault)
  • Short-circuit-protected: Yes
  • Open-circuit-proof: Yes
  • Parallel operation: No
  • Series operation: Yes, for 2 devices of the same type
  • MTBF: > 700,000 h (per IEC 61709)
  • Connection Data — Cable length (max.): 30 m
  • Connection 1 — Connection type: Input
  • Connection 1 — Connection technology: Push-in CAGE CLAMP®
  • Connection 1 — WAGO connector: picoMAX® 5.0, WAGO 2092 Series
  • Connection 1 — Solid conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
  • Connection 1 — Fine-stranded conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
  • Connection 1 — Strip length: 9 … 10 mm / 0.35 … 0.39 inches
  • Connection 2 — Connection type: Output
  • Connection 2 — Connection technology: Push-in CAGE CLAMP®
  • Connection 2 — WAGO connector: picoMAX® 3.5 (WAGO 2091 Series)
  • Connection 2 — Solid conductor: 0.2 … 1.5 mm² / 24 … 14 AWG
  • Connection 2 — Fine-stranded conductor: 0.2 … 1.5 mm² / 24 … 14 AWG
  • Connection 2 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
  • Width: 18 mm / 0.7 inches
  • Height: 90 mm / 3.543 inches
  • Depth: 55 mm / 2.165 inches
  • Depth from upper-edge of DIN-rail: 52.5 mm / 2.067 inches
  • Housing design: DIN-rail-mount enclosure
  • Mounting type: DIN-35 rail; Screw mount (back/side)
  • Flammability class per UL94: V2
  • Weight: 63 g
  • Ambient temperature (operation): -25 … +70 °C
  • Ambient temperature (storage): -40 … +85 °C
  • Relative humidity: 20 … 90 % (no condensation permissible)
  • Derating: -2.6 %/K (> 55 °C)
  • Climatic category: 3K3 (per EN 60721; except for low air pressure)
  • Conformity marking: CE
  • Standards/specifications: EN 61204-3; EN 60335-1; EN 62368; UL 62368; UL 508

Image shown is representative. Refer to the product specifications for the exact configuration.