null

WAGO 787-1211 Switched-mode power supply, Compact, 1-phase, 12 VDC output voltage, 5 A output current, DC-OK LED

$120.00
SKU:
787-1211
Shipping:
Calculated at Checkout
In Stock
Available
Before Ordering

Availability and lead times may vary. Request a quote if you need to confirm availability before placing your order.


Manufacturer Information

Wago orders require a $100 combined minimum order.

Family Owned Since 1932
Nationwide Shipping Serving all 50 states
Technical Support Product selection assistance
Project Assistance Quotes and sourcing support

Description

The WAGO 787-1211 switched-mode power supply features Compact, 1-phase, 12 VDC output voltage, 5 A output current, DC-OK LED.

Specifications

  • Phases: 1
  • Nominal input voltage [V]: 1 x AC 100 ... 240 V
  • Input voltage range: 1 x 85 … 264 VAC; 125 … 375 VDC
  • Input voltage derating: -2 %/V (< 100 VAC); -1.33 %/V (< 140 VDC)
  • Nominal mains frequency range: 47 … 63 Hz; 0 Hz
  • Input current Ii: ≤ 0.6 A
  • Inrush current: ≤ 30 A (NTC)
  • Power factor: ≥ 0.5
  • Power factor correction (PFC): Passive
  • Mains failure hold-up time: ≥ 600 ms (230 VAC); ≥ 12 ms (110 VAC)
  • Nominal output voltage [V]: 12 VDC (SELV)
  • Output voltage range: DC 12 V
  • Default Setting: 12 VDC
  • Nominal output current Io nom: 5 A
  • Nominal output power: 60 W
  • Deviation: ≤ 1 %
  • Deviation, dynamic load change 10 … 90 %: ≤ 1 %
  • Residual ripple: ≤ 100 mV (peak-to-peak)
  • Overload behavior: Constant power (in overload range: 1.22 … 1.7 x Io nom); Hiccup in the event of a short circuit or permanent overload
  • Signaling: 1 x DC OK LED (green)
  • Operation status indicator: Green LED (Uo)
  • Power loss Pl: ≤ 0.6 W
  • Power loss (max.) Pl (max.): 9 W (100 VAC / 12 VDC; 2.5 A)
  • Efficiency (typ.): 88.5 % (230 VAC; Nominal load); 87.5 % (110 VAC; Nominal load)
  • Internal fuse: T 3.15 A / 250 VAC
  • Pre-fuse (required): An external DC fuse is required for the DC input voltage.
  • Backup fuse (recommended): Circuit breaker: 6 A, 10 A or higher; Tripping characteristic: B
  • Isolation voltage (pri.-sec.): 4.242 kVDC
  • Isolation voltage (pri.-PE): 2.12 kVDC
  • Protection class: I
  • protection rating: IP20; per EN 60529
  • Reverse voltage protection: Yes
  • Resistance to reverse feed: ≤ 16 VDC
  • Overvoltage category: II
  • Pollution degree: 2
  • Transient suppression (primary): Varistor
  • Overvoltage protection; secondary: ≤ 20 VDC (in the event of a fault)
  • Short-circuit-protected: Yes
  • Open-circuit-proof: Yes
  • Parallel operation: Yes, for devices of the same type
  • Series operation: Yes, for 2 devices of the same type
  • MTBF: > 500,000 h (per IEC 61709)
  • Connection Data — Cable length (max.): 30 m
  • Connection 1 — Connection type: Input/output
  • Connection 1 — Connection technology: Push-in CAGE CLAMP®
  • Connection 1 — WAGO connector: picoMAX® 5.0, WAGO 2092 Series
  • Connection 1 — Solid conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
  • Connection 1 — Fine-stranded conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
  • Connection 1 — Strip length: 9 … 10 mm / 0.35 … 0.39 inches
  • Width: 72 mm / 2.835 inches
  • Height: 90 mm / 3.543 inches
  • Depth: 56 mm / 2.205 inches
  • Depth from upper-edge of DIN-rail: 52.5 mm / 2.067 inches
  • Note (dimensions): Depth: 48 mm (without cover)
  • Housing design: DIN-rail-mount enclosure
  • Mounting type: DIN-35 rail; Screw mount (back/side)
  • Flammability class per UL94: V0
  • Weight: 63 g
  • Ambient temperature (operation): -25 … +70 °C
  • Ambient temperature (storage): -40 … +85 °C
  • Relative humidity: 20 … 90 % (no condensation permissible)
  • Derating: -3 %/K (> 45 °C and Ui = 90 VAC); -2.3 %/K (> 50 °C and Ui = 230 VAC)
  • Climatic category: 3K3 (per EN 60721; except for low air pressure)
  • Conformity marking: CE
  • Standards/specifications: EN 61204-3; EN 60335-1; EN 62368-1; UL 60950-1; UL 508

Image shown is representative. Refer to the product specifications for the exact configuration.