null

WAGO 787-1642 EPSITRON® CLASSIC power supply, 3-phase, output voltage 24 VDC, 20 A, TopBoost

$485.90
SKU:
787-1642
Shipping:
Calculated at Checkout
In Stock
Available
Before Ordering

Availability and lead times may vary. Request a quote if you need to confirm availability before placing your order.


Manufacturer Information

Wago orders require a $100 combined minimum order.

Family Owned Since 1932
Nationwide Shipping Serving all 50 states
Technical Support Product selection assistance
Project Assistance Quotes and sourcing support

Description

The WAGO 787-1642 ePSITRON® CLASSIC power supply features 3-phase, output voltage 24 VDC, 20 A, TopBoost.

Specifications

  • Phases: 2 / 3
  • Nominal input voltage [V]: (2 / 3) x 400 … 500 VAC
  • Input voltage range: (2 / 3) x 320 … 575 VAC; 450 … 800 VDC
  • Nominal mains frequency range: 47 … 63 Hz; 0 Hz
  • Input current Ii: ≤ 3 x 1.21 A (400 VAC); ≤ 3 x 1.03 A (500 VAC)
  • Inrush current: ≤ 30 A (NTC)
  • Power factor correction (PFC): Passive
  • Mains failure hold-up time: ≥ 25 ms (500 VAC); ≥ 15 ms (400 VAC)
  • Nominal output voltage [V]: 24 VDC (SELV)
  • Output voltage range: DC 24 V
  • Default Setting: 24 VDC
  • Nominal output current Io nom: 20 A (24 VDC)
  • Nominal output power: 480 W
  • Deviation: ≤ 1 %
  • Residual ripple: ≤ 15 mV (peak-to-peak)
  • Current limitation: 1.1 x Io nom (typ.)
  • Overload behavior: Constant current
  • Signaling: 1 x DC OK LED (green); 1 x DC OK contact (make contact; max. 30 VAC/DC; 1 A)
  • Operation status indicator: Green LED (Uo)
  • Power loss Pl: ≤ 5.8 W; ≤ 42.8 W (400 VAC; nominal load)
  • Power loss (max.) Pl (max.): 47.6 W (500 VAC / 24 VDC; 20 A)
  • Efficiency (typ.): 92 %
  • Internal fuse: No
  • Pre-fuse (required): Alternative: motor circuit breaker; An external DC fuse is required for the DC input voltage.
  • Isolation voltage (pri.-sec.): 4.242 kVDC
  • Isolation voltage (pri.-PE): 2.2 kVDC
  • Isolation voltage (sec.-PE): 0.7 kVDC
  • Protection class: I
  • protection rating: IP20; per EN 60529
  • Resistance to reverse feed: ≤ 35 VDC
  • Overvoltage category: II
  • Pollution degree: 2
  • Transient suppression (primary): Varistor
  • Overvoltage protection; secondary: Internal protective circuit; ≤ 40 VDC (in the event of a fault)
  • Short-circuit-protected: Yes
  • Open-circuit-proof: Yes
  • Parallel operation: Yes
  • Series operation: Yes
  • MTBF: > 500,000 h (per IEC 61709)
  • Connection 1 — Connection type: Input/signaling
  • Connection 1 — Connection technology: CAGE CLAMP®
  • Connection 1 — WAGO connector: WAGO 721 Series
  • Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
  • Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
  • Connection 1 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
  • Connection 2 — Connection type: Output
  • Connection 2 — Connection technology: Push-in CAGE CLAMP®
  • Connection 2 — WAGO connector: WAGO 831 Series
  • Connection 2 — Solid conductor: 0.5 … 10 mm² / 20 … 8 AWG
  • Connection 2 — Fine-stranded conductor: 0.5 … 10 mm² / 20 … 8 AWG
  • Connection 2 — Strip length: 13 … 15 mm / 0.51 … 0.59 inches
  • Width: 80 mm / 3.15 inches
  • Height: 127 mm / 5 inches
  • Depth from upper-edge of DIN-rail: 180 mm / 7.087 inches
  • Mounting type: DIN-35 rail
  • Weight: 1623 g
  • Ambient temperature (operation): -25 … +70 °C (Device starts at -40 °C (type-tested))
  • Ambient temperature (storage): -25 … +85 °C
  • Relative humidity: 5 … 96 % (no condensation permissible)
  • Derating: -2.5 %/K (> 55 °C)
  • Conformity marking: CE
  • Standards/specifications: EN 61010-1; EN 61010-2-201; EN 61204-3; UL 60950-1; UL 508; DNV; SEMI F47

Image shown is representative. Refer to the product specifications for the exact configuration.