Description
The WAGO 787-1634 ePSITRON® CLASSIC power supply features 1-phase, output voltage 24 VDC, 20 A.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x 100 … 240 VAC; 1 x AC 100 … 240 V
- Input voltage range: 1 x 85 … 264 VAC; 120 … 300 VDC
- Input voltage derating: -1.8 %/V (< 105 VAC)
- Nominal mains frequency range: 44 … 66 Hz; 0 Hz
- Input current Ii: ≤ 2.23 A (230 VAC); ≤ 5.56 A (100 VAC)
- Inrush current: ≤ 30 A
- Power factor correction (PFC): Active
- Mains failure hold-up time: ≥ 20 ms (230 VAC); ≥ 8 ms (100 VAC)
- Nominal output voltage [V]: 24 VDC (SELV)
- Output voltage range: DC 24 V
- Default Setting: 24 VDC
- Nominal output current Io nom: 20 A (24 VDC)
- Nominal output power: 480 W
- Deviation: ≤ 1 %
- Residual ripple: ≤ 70 mV (peak-to-peak)
- Current limitation: 1.1 x Io nom (typ.)
- Overload behavior: Constant current
- TopBoost: See instruction leaflet
- Signaling: 1 x DC OK LED (green); 1 x DC OK contact (make contact; max. 30 VAC/DC; 1 A)
- Operation status indicator: Green LED (Uo)
- Power loss Pl: ≤ 7.2 W; ≤ 42.4 W (230 VAC; nominal load)
- Power loss (max.) Pl (max.): 68.3 W (100 VAC / 24 VDC; 20 A)
- Efficiency (typ.): 92 %
- Internal fuse: T 10 A / 250 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): Circuit breaker: 10 A, 16 A; Tripping characteristic: B or C
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Isolation voltage (pri.-PE): 2.2 kVDC
- Isolation voltage (sec.-PE): 0.7 kVDC
- Protection class: I
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 35 VDC
- Overvoltage category: II
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Overvoltage protection; secondary: Internal protective circuit; ≤ 40 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 500,000 h (per IEC 61709)
- Connection 1 — Connection type: Input/signaling
- Connection 1 — Connection technology: CAGE CLAMP®
- Connection 1 — WAGO connector: WAGO 721 Series
- Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
- Connection 2 — Connection type: Output
- Connection 2 — Connection technology: Push-in CAGE CLAMP®
- Connection 2 — WAGO connector: WAGO 831 Series
- Connection 2 — Solid conductor: 0.5 … 10 mm² / 20 … 8 AWG
- Connection 2 — Fine-stranded conductor: 0.5 … 10 mm² / 20 … 8 AWG
- Connection 2 — Strip length: 13 … 15 mm / 0.51 … 0.59 inches
- Width: 95 mm / 3.74 inches
- Height: 127 mm / 5 inches
- Depth from upper-edge of DIN-rail: 170 mm / 6.693 inches
- Mounting type: DIN-35 rail
- Weight: 1600 g
- Ambient temperature (operation): -25 … +70 °C (Device starts at -40 °C (type-tested))
- Ambient temperature (storage): -25 … +85 °C
- Relative humidity: 5 … 96 % (no condensation permissible)
- Derating: -5 %/K (> 60 °C, 196 … 264 VAC); -2.5 %/K (> 50 °C, 85 … 195 VAC)
- Climatic category: 3K3 (per EN 60721)
- Conformity marking: CE
- Standards/specifications: EN 61010-1; EN 61010-2-201; EN 61204-3; UL 60950-1; UL 508; DNV; SEMI F47
Image shown is representative. Refer to the product specifications for the exact configuration.