Description
The WAGO 2787-2144 power supply features Pro 2, 1-phase, 24 VDC output voltage, 5 A output current, TopBoost + PowerBoost, communication capability.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x 100 … 240 VAC
- Input voltage range: 1 x 90 … 264 VAC
- Nominal mains frequency range: 50 … 60 Hz
- Input current Ii: ≤ 1 A (240 VAC; Nominal load); ≤ 1.8 A (100 VAC; Nominal load)
- Inrush current: ≤ 9 A (after 1 ms)
- Power factor correction (PFC): Active
- Mains failure hold-up time: ≥ 20 ms (230 VAC)
- Nominal output voltage [V]: 24 VDC (SELV)
- Output voltage range: DC 24 V
- Default Setting: 24 VDC
- Nominal output current Io nom: 5 A (24 VDC)
- Nominal output power: 120 W
- Deviation: ≤ 1 %
- Residual ripple: ≤ 70 mV (peak-to-peak)
- Current limitation: 1.1 x Io nom (typ.)
- Overload behavior: TopBoost/PowerBoost/Time-limited constant current mode (other overload behaviors can be set)
- PowerBoost: 7.5 ADC (5 s)
- TopBoost: Up to 600 %
- Signaling: Optical status indication (DC OK; load; warning and error states); Digital signal input and output (DI/DO)
- Communications: EtherNet/IPTM (2789-9023 Communication Module); USB (750-923 Communication Cable); Ethernet/IP (2789-9023 Communication Module); IO-Link (2789-9080 Communication Module); Modbus RTU (Communication Module 2789-9015); Modbus TCP (2789-9052 Communication Module)
- Power loss Pl: ≤ 1 W (standby); ≤ 2 W (no load); ≤ 10 W (230 VAC; nominal load)
- Efficiency (typ.): 93.8 % (230 VAC; 5 A; 25 °C)
- Internal fuse: T 6.3 A / 250 VAC
- Backup fuse (recommended): 16 A (for USA/Canada: 15 A)
- Isolation voltage (pri.-sec., AC): 3,510 V
- Isolation voltage (pri.-PE, AC): 2,200 V
- Isolation voltage (sec.-PE): 0.5 kVDC
- Isolation voltage (sec.-signal): 0.5 kVDC
- Protection class: I
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 35 VDC
- Overvoltage category: III (≤ 2000 m a.s.l.); II (> 2000 m a.s.l.)
- Pollution degree: 2
- Transient suppression (primary): Yes
- Overvoltage protection; secondary: Internal protective circuit; ≤ 35 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 1,000,000 h (per IEC 61709)
- Connection 1 — Connection type: Input/output/signaling
- Connection 1 — Connection technology: CAGE CLAMP®
- Connection 1 — WAGO connector: WAGO 721 Series
- Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor; with insulated ferrule: 2.5 … 1.5 mm² / 12 … 16 AWG
- Connection 1 — Fine-stranded conductor; with uninsulated ferrule: 1.5 … 0.08 mm² / 16 … 28 AWG
- Connection 1 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
- Width: 35 mm / 1.378 inches
- Height: 130 mm / 5.118 inches
- Depth from upper-edge of DIN-rail: 130 mm / 5.118 inches
- Note (dimensions): Height without connector; Height with connector: 166 mm
- Mounting type: DIN-35 rail
- Weight: 650 g
- Ambient temperature (operation): -25 … +70 °C (Device starts at -40 °C (type-tested))
- Ambient temperature (storage): -40 … +85 °C
- Relative humidity: 5 … 96 % (no condensation permissible)
- Derating: See instruction leaflet
- Climatic category: 3K3 (per EN 60721)
- Operating altitude (max.): 5000 m
- Conformity marking: CE
- Standards/specifications: UL 121201 (HazLoc); EN 61010-2-201; EN 61204-3; UL 61010-1; UL 61010-2-201; SEMI F47
Image shown is representative. Refer to the product specifications for the exact configuration.