Description
The WAGO 787-854 ePSITRON® PRO Power supply features three-phase, output voltage 24 VDC, 40 A, PowerBoost, LineMonitor.
Specifications
- Phases: 2 / 3
- Nominal input voltage [V]: (2 / 3) x 400 … 500 VAC; (2 / 3) x AC 400 … 500 V
- Input voltage range: (2 / 3) x 340 … 550 VAC; 480 … 780 VDC
- Nominal mains frequency range: 50 … 60 Hz; 0 Hz
- Input current Ii: ≤ 3 x 2 A (340 VAC)
- Inrush current: ≤ 30 A
- Power factor correction (PFC): Passive (adjustable via software/display)
- Mains failure hold-up time: ≥ 15 ms (3 x 400 VAC)
- Nominal output voltage [V]: 24 VDC (SELV)
- Output voltage range: DC 24 V
- Default Setting: 24 VDC
- Nominal output current Io nom: 40 A (24 VDC)
- Nominal output power: 960 W
- Deviation: ≤ 1 %
- Residual ripple: ≤ 70 mV (peak-to-peak)
- Current limitation: 1.1 x Io nom (typ.)
- Overload behavior: Adjustable (constant current/fuse mode)
- PowerBoost: 60 ADC (4 s); 50 ADC (16 s)
- TopBoost: 100 ADC (50 ms)
- Signaling: 1 x DC OK LED (green); 1 x Warning LED (yellow); 1 x Error LED (red); LCD; 4 x Signal output (24 VDC; max. 25 mA); 1 x RS-232 interface
- Operation status indicator: Green LED (DC OK); Yellow LED (warning); Red LED (error)
- Communications: RS-232 serial interface
- Power loss Pl: ≤ 7 W; ≤ 61.5 W (nominal load)
- Efficiency (typ.): 93.6 %
- Internal fuse: 3 x T 3.2 A / 440 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): 3 x Circuit breaker: 6 A, 10 A, 16 A; Tripping characteristic: B or C; Alternative: motor circuit breaker; Setpoint: 3.2 A; Setting range: 2.5 … 4 A
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Isolation voltage (pri.-PE): 2.2 kVDC
- Isolation voltage (sec.-PE): 0.7 kVDC
- Protection class: I
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 35 VDC
- Overvoltage category: II
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 500,000 h (per IEC 61709)
- Connection 1 — Connection type: Input
- Connection 1 — Connection technology: CAGE CLAMP®
- Connection 1 — WAGO connector: WAGO 231 Series
- Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
- Connection 2 — Connection type: Output
- Connection 2 — Connection technology: Push-in CAGE CLAMP®
- Connection 2 — WAGO connector: WAGO 831 Series
- Connection 2 — Solid conductor: 0.5 … 10 mm² / 20 … 8 AWG
- Connection 2 — Fine-stranded conductor: 0.5 … 10 mm² / 20 … 8 AWG
- Connection 2 — Strip length: 13 … 15 mm / 0.51 … 0.59 inches
- Connection 3 — Connection type: Signaling
- Connection 3 — Connection technology: CAGE CLAMP®
- Connection 3 — WAGO connector: WAGO 733 Series
- Connection 3 — Solid conductor: 0.08 … 0.5 mm² / 28 … 20 AWG
- Connection 3 — Fine-stranded conductor: 0.08 … 0.5 mm² / 28 … 20 AWG
- Connection 3 — Strip length: 5 … 6 mm / 0.2 … 0.24 inches
- Width: 128 mm / 5.039 inches
- Height: 171 mm / 6.732 inches
- Depth from upper-edge of DIN-rail: 205 mm / 8.071 inches
- Note (dimensions): Height with connector
- Mounting type: DIN-35 rail
- Weight: 2300 g
- Ambient temperature (operation): -25 … +55 °C (Device starts at -40 °C (type-tested))
- Ambient temperature (storage): -25 … +85 °C
- Relative humidity: 5 … 96 % (no condensation permissible)
- Derating: -5 %/K (> 45 °C)
- Climatic category: 3K3 (per EN 60721)
- Conformity marking: CE
- Standards/specifications: EN 61010-1; EN 61010-2-201; EN 61204-3; EN 61558-2-16; UL 60950; UL 508
Image shown is representative. Refer to the product specifications for the exact configuration.