Description
The WAGO 787-1611 ePSITRON® CLASSIC power supply features single-phase, output voltage 12 VDC, 4 A.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x 100 … 240 VAC
- Input voltage range: 1 x 85 … 264 VAC; 120 … 300 VDC
- Input voltage derating: -2.5 %/V (< 95 VAC)
- Nominal mains frequency range: 44 … 66 Hz; 0 Hz
- Input current Ii: ≤ 0.46 A (240 VAC); ≤ 0.86 A (100 VAC)
- Inrush current: ≤ 30 A
- Power factor correction (PFC): Passive
- Mains failure hold-up time: ≥ 120 ms (230 VAC); ≥ 15 ms (100 VAC)
- Nominal output voltage [V]: 12 VDC (SELV)
- Output voltage range: DC 12 V
- Default Setting: 12 VDC
- Nominal output current Io nom: 4 A (12 VDC); 4.2 A (< 40 °C)
- Nominal output power: 48 W
- Deviation: ≤ 1 %
- Residual ripple: ≤ 20 mV (peak-to-peak)
- Current limitation: 1.1 x Io nom (typ.)
- Overload behavior: Constant current
- Signaling: 1 x DC OK LED (green); 1 x Active signal output DC OK (12 VDC; 40 mA)
- Operation status indicator: Green LED (Uo)
- Power loss Pl: ≤ 1 W; ≤ 8 W (230 VAC; nominal load)
- Power loss (max.) Pl (max.): 9.1 W (100 VAC / 12 VDC; 4 A)
- Efficiency (typ.): 86 %
- Internal fuse: T 4 A / 250 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): Circuit breaker: 6 A, 10 A, 16 A; Tripping characteristic: B or C
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Protection class: II
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 25 VDC
- Overvoltage category: II
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Overvoltage protection; secondary: Internal protective circuit; ≤ 35 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 500,000 h (per IEC 61709)
- Connection 1 — Connection type: Input/output/signaling
- Connection 1 — Connection technology: CAGE CLAMP®
- Connection 1 — WAGO connector: WAGO 721 Series
- Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Strip length: 8 … 9 mm / 0.31 … 0.35 inches
- Width: 45 mm / 1.772 inches
- Height: 90 mm / 3.543 inches
- Depth from upper-edge of DIN-rail: 107.5 mm / 4.232 inches
- Mounting type: DIN-35 rail
- Weight: 257.6 g
- Ambient temperature (operation): -25 … +70 °C (Device starts at -40 °C (type-tested))
- Ambient temperature (storage): -25 … +85 °C
- Relative humidity: 5 … 96 % (no condensation permissible)
- Derating: -3 %/K (> 50 °C)
- Climatic category: 3K3 (per EN 60721)
- Conformity marking: CE
- Standards/specifications: EN 61010-1; EN 61010-2-201; EN 61204-3; EN 60335-1; UL 60950-1; UL 508; DNV; SEMI F47
Image shown is representative. Refer to the product specifications for the exact configuration.