Description
The WAGO 787-1216 ePSITRON® COMPACT power supply features single-phase, output voltage 24 VDC, 4 A, with pluggable picoMAX connector.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x 100 … 240 VAC
- Input voltage range: 1 x 85 … 264 VAC; 125 … 375 VDC
- Input voltage derating: -2 %/V (< 100 VAC); -1.33 %/V (< 140 VDC)
- Nominal mains frequency range: 47 … 63 Hz; 0 Hz
- Input current Ii: ≤ 2.5 A
- Inrush current: ≤ 20 A
- Power factor: ≥ 0.5
- Power factor correction (PFC): Passive
- Mains failure hold-up time: ≥ 50 ms
- Nominal output voltage [V]: 24 VDC (SELV)
- Output voltage range: DC 24 V
- Default Setting: 24 VDC
- Nominal output current Io nom: 4.2 A; 3.3 A (< 110 VAC)
- Nominal output power: 100 W
- Deviation: ≤ 1 %
- Deviation, dynamic load change 10 … 90 %: ≤ 1 %
- Residual ripple: ≤ 100 mV (peak-to-peak)
- Overload behavior: Constant power (in overload range: 1.05 … 1.35 x Io nom); Shutdown and automatic restart in the event of a short circuit or permanent overload
- Signaling: 1 x DC OK LED (green)
- Operation status indicator: Green LED (Uo)
- Power loss Pl: ≤ 0.7 W
- Power loss (max.) Pl (max.): 15 W (100 VAC / 24 VDC; 4.2 A)
- Efficiency (typ.): 90 % (230 VAC); 87 % (110 VAC)
- Internal fuse: T 3.15 A / 500 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): Circuit breaker: 6 A (C characteristic), 10 A (B characteristic) or higher
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Protection class: I
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 35 VDC
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Overvoltage protection; secondary: ≤ 31 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 500,000 h (per IEC 61709)
- Connection 1 — Connection type: Input/output
- Connection 1 — Connection technology: Push-in CAGE CLAMP®
- Connection 1 — WAGO connector: picoMAX® 5.0, WAGO 2092 Series
- Connection 1 — Solid conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.2 … 2.5 mm² / 24 … 12 AWG
- Connection 1 — Strip length: 9 … 10 mm / 0.35 … 0.39 inches
- Width: 108 mm / 4.252 inches
- Height: 90 mm / 3.543 inches
- Depth: 56 mm / 2.205 inches
- Depth from upper-edge of DIN-rail: 52.5 mm / 2.067 inches
- Note (dimensions): Depth: 48 mm (without cover)
- Housing design: DIN-rail-mount enclosure
- Mounting type: DIN-35 rail; Screw mount (back/side)
- Flammability class per UL94: V0
- Weight: 456.9 g
- Ambient temperature (operation): -25 … +70 °C
- Ambient temperature (storage): -40 … +85 °C
- Relative humidity: ≤ 95 % (no condensation permissible)
- Derating: -2.66 %/K (> 55 °C)
- Climatic category: 3K3 (per EN 60721; except for low air pressure)
- Conformity marking: CE
- Standards/specifications: EN 61204-3; EN 60335-1; EN 62368-1; UL 60950-1; UL 508
Image shown is representative. Refer to the product specifications for the exact configuration.