Description
The WAGO 787-1012 ePSITRON ® COMPACT power supply features single-phase, 24 VDC, 2.5 A.
Specifications
- Phases: 1
- Nominal input voltage [V]: 1 x 100 … 240 VAC
- Input voltage range: 1 x 85 … 264 VAC; 120 … 300 VDC
- Input voltage derating: Io ≤ 2 A (< 100 VAC); Io ≤ 1.8 A (< 90 VAC)
- Nominal mains frequency range: 44 … 66 Hz; 0 Hz
- Input current Ii: ≤ 0.6 A (230 VAC); ≤ 1.4 A (110 VAC)
- Inrush current: ≤ 30 A (NTC)
- Power factor correction (PFC): Passive
- Mains failure hold-up time: ≥ 80 ms (230 VAC); ≥ 10 ms (110 VAC)
- Nominal output voltage [V]: 24 VDC (SELV)
- Output voltage range: DC 24 V
- Default Setting: 24 VDC
- Nominal output current Io nom: 2.5 A (24 VDC); 1.6 A (in any mounting position)
- Nominal output power: 60 W
- Deviation: ≤ 2 %
- Residual ripple: ≤ 100 mV (peak-to-peak)
- Current limitation: 1.1 x Io nom (typ.)
- Overload behavior: Constant current
- Signaling: 1 x Status indication LED (green)
- Operation status indicator: Green LED (Uo)
- Power loss Pl: ≤ 2.2 W; ≤ 8.5 W (230 VAC; nominal load)
- Power loss (max.) Pl (max.): 10.5 W (100 VAC / 24 VDC; 2.5 A)
- Efficiency (typ.): 88 %
- Internal fuse: T 2 A / 250 VAC
- Pre-fuse (required): An external DC fuse is required for the DC input voltage.
- Backup fuse (recommended): Circuit breaker: 6 A (C characteristic), 10 A (B characteristic) or higher
- Isolation voltage (pri.-sec.): 4.242 kVDC
- Protection class: II
- protection rating: IP20; per EN 60529
- Resistance to reverse feed: ≤ 30 VDC
- Overvoltage category: II
- Pollution degree: 2
- Transient suppression (primary): Varistor
- Overvoltage protection; secondary: ≤ 40 VDC (in the event of a fault)
- Short-circuit-protected: Yes
- Open-circuit-proof: Yes
- Parallel operation: Yes
- Series operation: Yes
- MTBF: > 500,000 h (per IEC 61709)
- Connection 1 — Connection type: Input/output
- Connection 1 — Connection technology: CAGE CLAMP®
- Connection 1 — WAGO connector: WAGO 740 Series
- Connection 1 — Solid conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Fine-stranded conductor: 0.08 … 2.5 mm² / 28 … 12 AWG
- Connection 1 — Strip length: 6 … 7 mm / 0.24 … 0.28 inches
- Width: 72 mm / 2.835 inches
- Height: 89 mm / 3.504 inches
- Depth: 59 mm / 2.323 inches
- Depth from upper-edge of DIN-rail: 55 mm / 2.165 inches
- Housing design: DIN-rail-mount enclosure
- Mounting type: DIN-35 rail
- Flammability class per UL94: V0
- Weight: 271 g
- Ambient temperature (operation): -25 … +60 °C (Device starts at -40 °C (type-tested))
- Ambient temperature (storage): -25 … +80 °C
- Ambient temperature UL (operation at UN): -25 … +55 °C
- Relative humidity: 5 … 96 % (no condensation permissible)
- Derating: -3 %/K (> 45 °C)
- Climatic category: 3K3 (per EN 60721)
- Conformity marking: CE
- Standards/specifications: EN 61010-1; EN 61010-2-201; EN 61204-3; UL 60950-1; UL 508; DNV
Image shown is representative. Refer to the product specifications for the exact configuration.