Description
The WAGO 750-672 stepper Controller features 70 VDC, 7.5 A.
Specifications
- Device-specific: Inputs (preset): DI 1: Drive stop, DI 2: Reference input, DI 3: Jog switch in positive direction, DI 4: Jog switch in negative direction, DI 5: Limit switch in positive direction, DI 6: Limit switch in negative direction, Outputs (preset): DO 1: Target reached, DO 2: Error, Inputs and outputs can be freely reconfigured.
- Number of digital outputs: 2
- Input filter: 100 µs, software filter can be connected
- Input current (typ.): 2.8 mA
- Output current per channel: 0.5 A
- Output current: short-circuit-protected
- Switching frequency (max.): 5 Hz; Inductive load per IEC 947-5-1, DC 13
- Load type: Resistive load, inductive load (max. 2 H), lamps
- Output current (max.) (motor): 2 x 5.0 A (2 x 7.5 A transient)
- Output voltage: Control voltage: 24 VDC (-25 … +30 %); closed current: 120 mA + 2 x 0.5 A (DO1, DO2, load-dependent); Motor voltage: 55 VDC nominal value; absolute upper limit: 71.5 V; absolute lower limit: 18 V; closed current (typ.) = 5 mA; protection via external fuse 5 A
- Voltage range for signal (0): −3 … +5 VDC
- Voltage range for signal (1): 15 … 30 VDC
- Diagnostics: Overcurrent, short circuit or ground fault, overtemperature, supply voltage monitoring, motor wire break
- Resolution: 15 bits + 16 bit prescaler; 64 microsteps per full step
- Stepper resolution: 23 bits + sign bit
- Stepper frequency (full-step) max.: 7,812 Hz
- Data width: 12-byte input/output
- Protection: Short circuit monitoring of motor connections: Winding short circuit and short circuit to 0 V and 24 V 24 V supply: Reverse voltage protection Motor supply: Reverse voltage protection via external fuse
- Function: Positioning, sin²-shaped ramps, setpoint change on the fly, speed control
- Supply voltage (system): 5 VDC; via data contacts
- Current consumption (system supply): 70 mA
- Isolation: 500 V system/field
- Indicators: LED (A) red: Error; LED (B, C) yellow: Operation, Run Program Active; LED (D, E, F) green: Enable, Control Voltage, Motor Voltage
- Connection Data — Connection technology: inputs / outputs: 24 x CAGE CLAMP®
- Connection Data — Connectable conductor materials: Copper
- Connection Data — Connection type: Inputs/Outputs
- Connection Data — Solid conductor: 0.08 … 1.5 mm² / 28 … 14 AWG
- Connection Data — Fine-stranded conductor: 0.08 … 1.5 mm² / 28 … 14 AWG
- Connection Data — Strip length: 5 … 6 mm / 0.2 … 0.24 inches
- Connection Data — Connection requirement (permissible cable length): 30 m
- Connection Data — Connection requirement (permissible cable type): Motor connection: shielded
- Connection Data — Note (conductor cross-section): 14 AWG: THHN, THWN
- Width: 48 mm / 1.89 inches
- Height: 100 mm / 3.937 inches
- Depth: 69.8 mm / 2.748 inches
- Depth from upper-edge of DIN-rail: 62.6 mm / 2.465 inches
- Mounting type: DIN-35 rail
- Pluggable connector: fixed
- Color: light gray
- Housing material: Polycarbonate; polyamide 6.6
- Weight: 175 g
- Conformity marking: CE
- Ambient temperature (operation): 0 … +55 °C
- Ambient temperature (storage): -40 … +85 °C
- Protection type: IP20
- Pollution degree: 2 per IEC 61131-2
- Operating altitude: 0 … 2000 m / 0 … 6562 ft
- Mounting position: Horizontal left, horizontal right, horizontal top, horizontal bottom, vertical top and vertical bottom
- Relative humidity (without condensation): 95 %
- Vibration resistance: Per IEC 60068-2-6
- Shock resistance: 15g per IEC 60068-2-27
- EMC immunity to interference: per EN 61000-6-2
- EMC emission of interference: per EN 61000-6-3
- Exposure to pollutants: Per IEC 60068-2-42 and IEC 60068-2-43
- Permissible pollutant concentration H2S at a relative humidity < 75%: 10 ppm
- Permissible pollutant concentration SO 2 at a relative humidity < 75%: 25 ppm
Image shown is representative. Refer to the product specifications for the exact configuration.